← How-Tos
3d-printing 6 days ago ◑ 10 views ◯ 4 min read

Creality Hi Complete Setup Guide: Unboxing, Calibration, and Your First Print

Creality HiKlipperCoreXY3D printer setupinput shaperbed leveling

The Creality Hi is Creality's push into the higher-end CoreXY segment that Bambu Lab's P1/X1 line and the K-series have been competing in for a few years now, aimed at buyers who want Klipper-based speed and a closed-loop auto-leveling experience without stepping up to Creality's largest K2 Plus format. This guide covers unboxing, the pre-flight checks that matter most on a CoreXY machine this size, calibration, and your first print.

Unboxing and Pre-Assembly Checks

The Hi ships mostly pre-assembled in its CoreXY gantry, with final setup limited to mounting the top frame extrusions, running the belt-driven gantry cables, and seating the enclosure panels. Before powering on:

Firmware, Network Setup, and Klipper

The Hi runs on Creality's Klipper-based firmware stack, the same general approach used on the K1/K2 series, which means most of what you already know about Klipper macros, input shaper, and the Moonraker/Fluidd web interface carries over directly. Connect it to your network over WiFi during first-boot setup and confirm you can reach its web control panel before doing any calibration — this gives you Moonraker API access for anything beyond the touchscreen's basic controls, including remote job monitoring and camera streaming if your unit has the onboard camera module.

Input Shaper and Resonance Calibration

Run Klipper's `SHAPER_CALIBRATE` routine before your first real print, not just the standard bed leveling — this is the single calibration step most new CoreXY owners skip and then wonder why their prints show ringing on fast moves. The Hi's higher-speed CoreXY gantry means uncorrected resonance shows up more visibly than it would on a slower bed-slinger. Run the calibration with an accelerometer-equipped toolhead (built in on most Hi configurations) and let Klipper auto-select input shaper type and frequency for both X and Y axes independently — don't assume both axes need the same shaper settings, since toolhead mass and belt path length differ between them on a CoreXY frame.

Bed Leveling, Z-Offset, and First Layer

Run the auto bed-leveling mesh probe routine, then dial in Z-offset with a first-layer test print rather than trusting the probe's reported zero blindly — probe-based systems on every CoreXY printer in this class can be off by a small but print-ruining amount if the nozzle has any filament residue on the tip during probing. Clean the nozzle tip before probing, every time, as standard practice.

StepWhy it matters on the Hi specifically Clean nozzle before probingResidue on the tip skews probe-reported Z by enough to cause first-layer issues Run input shaper before first printCoreXY gantry speed makes uncorrected ringing more visible than on slower machines Check enclosure door sealChamber heating for ABS/ASA depends on it holding temperature Verify belt tension on both loopsCoreXY kinematics mean uneven tension shows up as diagonal-move ghosting

Your First Print

Start with Creality's bundled PLA or PETG profile and a simple benchmark model rather than jumping straight to a large or technically demanding print — the goal of the first print is confirming extrusion, bed adhesion, and motion quality are all healthy, not testing the printer's upper speed limits. Once a clean first print confirms the baseline, move on to higher-temperature engineering filaments; the Hi's enclosure and chamber heating make it a genuinely capable ABS and ASA printer if you've confirmed the door seal and chamber temperature hold steady during a test print first.

Most of the trouble reports on CoreXY machines in the Hi's class trace back to skipping input shaper calibration or not checking belt tension evenly across both loops, not to the printer itself being unreliable. Spend the extra fifteen minutes on resonance calibration and a clean-nozzle Z-offset check before your first print, and the Hi settles in as a fast, enclosure-capable machine that holds up well for both standard filaments and the higher-temperature materials its chamber heating is built for.