← Projects
laser intermediate 14 days ago ◑ 17 views ◯ 5 min read

Build a Laser-Cut Pinball-Style Tabletop Game with Switches and Scoring

Build time: One long weekend (10-12 hours of cutting, wiring, and assembly)
Tools needed: CO2 or diode laser cutter with LightBurn, soldering iron, drill with small bits for switch mounting, wood glue, small clamps, wire strippers, multimeter
laser cuttingpinballtabletop gamearduinomicroswitchscoringplywoodacryliclaser project
Parts List

A laser cutter is a genuinely good tool for building a tabletop pinball-style game: the playfield, walls, ramps, and target mounts are all flat parts that assemble into a 3D structure, which is exactly the kind of project laser cutting excels at compared to the equivalent build in hand tools. This project builds a compact tabletop machine — roughly the footprint of a large cutting board — with a spring plunger, a handful of switch-triggered targets, simple flipper-less ramps, and an Arduino-driven digital scoreboard. It's not a full-size pinball machine, but it captures the mechanics in a build that fits on a bench and is genuinely achievable in a weekend.

Designing the Playfield in LightBurn

Lay out the playfield as a single base panel in 6mm plywood with pocket cuts (cut most of the way through, not all the way) for switch and standoff mounting points, surrounded by a perimeter wall built from separate upright panels joined with finger joints at the corners for strength. Route the ball's main path with a gentle outer lane along one side (fed by the plunger) that funnels into the open playfield, and keep ramps simple — a laser-cut plywood ramp with acrylic side rails is far easier to build reliably than anything with curves or multiple elevation changes. Design target pockets as small walled enclosures sized to fit a microswitch's lever with 2-3mm of clearance so the ball reliably trips it without getting stuck.

Keep your kerf compensation in mind for every slot and tab — Baltic birch plywood this site covers elsewhere commonly needs a kerf offset of roughly 0.1-0.15mm depending on your laser and speed/power settings, and on a project with this many interlocking finger joints, an uncompensated kerf is the difference between a snug box and a loose, rattly one.

Cutting and Assembling the Frame and Playfield

Cut all plywood parts from 6mm stock for structural panels (walls, base, ramp supports) and use 3mm plywood or clear acrylic for ramps and sight-lines where you want to see the ball or reduce weight. Dry-fit the entire box before gluing anything — finger-jointed laser-cut boxes are forgiving to adjust at the dry-fit stage and very unforgiving once glue has set, especially if a kerf offset was slightly off on one panel. Glue the perimeter walls to the base first, clamp until set, then install ramps and target walls as a second pass once the main structure is rigid.

Wiring Target Switches to an Arduino Scorekeeper

Each target switch is a simple normally-open leaf microswitch wired to a digital input pin with an internal pull-up enabled in software (INPUT_PULLUP), with the switch's other leg going to ground — this means a target registers as a hit when the ball depresses the lever and the pin reads LOW, and needs no external pull-up resistors wired on the board itself. Debounce every switch in software with a simple time-based debounce (ignore any additional LOW reading within roughly 20-30ms of the last registered hit) — mechanical leaf switches bounce readings for a few milliseconds on contact, and without debouncing you'll see a single ball hit register as two or three points instead of one.

ComponentArduino PinNotes Target switches (×4-6)Digital pins 2-7INPUT_PULLUP, switch to GND TM1637 display CLK/DIODigital pins 8/9Scoreboard output Tilt/drain switch (ball return sensing)Digital pin 10Optional — detects ball leaving playfield to reset for next launch

Drive the scoreboard from a TM1637 module over its simple two-wire protocol rather than wiring a raw 7-segment display directly — it needs far fewer Arduino pins and handles digit multiplexing in its own onboard controller, which matters once you're already using most of an Uno's digital pins for switches.

Spring Plunger and Ball Return Lane

Build the plunger as a laser-cut sled riding in a slotted channel, pulled back against a compression spring and released to strike the ball — size the spring from the assortment kit by test-fitting; too stiff and the ball jumps the lane on launch, too soft and it won't reliably clear the outer lane's first curve. Line the plunger channel and the ball's main lanes with a thin strip cut from the rubber O-ring stock (sliced open and laid flat) to quiet the ball's travel noise and reduce wear on the plywood lane edges over repeated play.

Firmware Notes

Keep the scoring logic simple to start: each target has a fixed point value, the Arduino sums hits and pushes the running total to the display after every registered hit, and a drain switch at the bottom of the playfield resets the ball-in-play state so the next plunger pull starts a fresh round rather than continuing to add to the same ball's score indefinitely. This is a good first project for anyone who hasn't done switch-based scorekeeping before — there's no need for anything more complex than digitalRead, a debounce timer, and an integer running total.

Safety Notes

The compression spring in the plunger stores real energy at full compression — assemble and test the plunger mechanism with the spring at low preload first, and keep fingers clear of the direct line of travel when testing at full power. Steel pinballs are a choking hazard and a genuine projectile risk if a spring or ramp fails unexpectedly, so this is not a build to leave within reach of small children unsupervised. If you're cutting acrylic for the ramps or sight panels on a CO2 laser, follow standard laser ventilation practice this site covers elsewhere — acrylic fumes in a confined space add up over a long cutting session.

Once the core mechanics are working, this is an easy platform to keep building on — additional targets, a simple kickback lane, or even a second plunger lane are all straightforward additions to the same Arduino-based scoring approach once the base machine is solid.