Build a CNC-Routed Modular Tool Chest with Drawer Slides and Dividers
- 18mm Baltic birch plywood 4x8 sheet
- 12mm Baltic birch plywood 4x8 sheet
- soft-close ball bearing drawer slides 18 inch
- drawer pulls brushed nickel
- wood screws assorted sizes
- titebond III wood glue
- edge banding iron-on birch veneer
- danish oil wood finish
- threaded inserts M6 for wood
- adjustable leveling feet for furniture
- 4mm pegboard hardboard sheet
- double sided carpet tape for CNC spoilboard
A rolling tool cabinet from a big-box store is stamped steel, generic drawer sizes, and a price tag that keeps climbing. This project is the CNC-routed alternative: a modular plywood tool chest built from a small set of repeated drawer-box parts, sized exactly to what you actually own, with dadoed dividers you can rearrange as your tool collection changes. Everything is cut on a desktop CNC router from flat 18mm and 12mm plywood, using tabbed and dadoed joinery that assembles with glue and screws rather than requiring a dovetail jig or a table saw full of jigs.
The design here is a single carcass with four drawer openings, each drawer built as its own box riding on a pair of ball-bearing slides, with a removable pegboard back panel for frequently grabbed hand tools. The dimensions below assume a 30in wide by 20in deep by 32in tall chest, but the whole thing is parametric by nature โ every panel is a flat rectangle with pocketed dados, so scaling it to your own tool collection and CNC bed size is mostly a matter of changing numbers in your CAM file rather than redesigning joinery.
Planning the Carcass
Lay out the four main carcass panels โ two sides, a top, and a bottom โ plus a full-depth back panel and a center divider if you're running two columns of drawers rather than one wide column. Cut all structural joints as dados rather than butt joints: a 12mm-wide, half-the-panel-thickness-deep dado pocketed directly in your CAM software gives you self-aligning glue joints that don't rely on clamping pressure alone to stay square during assembly.
- Side panels: 20in deep x 32in tall, with dados cut for the top, bottom, and any internal shelf dividers.
- Top and bottom panels: 30in wide x 20in deep, sized to fit between the side panel dados.
- Back panel: full 30in x 32in, rabbeted into the sides rather than dadoed, since it also serves as the structural element that keeps the whole carcass square.
- If your CNC bed is smaller than these panels, split the design into bolt-together sub-sections with a mating batten strip rather than trying to cut oversized panels in multiple passes โ it's more reliable and easier to transport if you ever need to move the finished chest.
Cutting the Carcass and Drawer Boxes
- Rough-cut your plywood sheets to a size that fits your spoilboard with enough margin for clamping or vacuum hold-down, then square one edge against a fence before loading your actual cut files โ plywood sheet edges from the store are rarely square enough to reference directly.
- Run a profile pass around each panel's outline with a compression bit sized for your plywood thickness โ compression bits give you a clean top surface and a clean bottom surface simultaneously, which matters a lot on 12mm drawer-box plywood where both faces show.
- Pocket all dados and rabbets in a second pass with a smaller bit (1/4in works well for 18mm stock), cutting to roughly half the panel's thickness for interlocking strength without cutting all the way through.
- Cut drawer box parts โ front, back, two sides, and a bottom captured in a shallow groove โ as four identical sets sized to your chosen slide length, leaving 1/2in clearance on each side of the drawer box width for the slide hardware itself.
- Drill the pegboard back panel pattern (standard 1in on-center hole spacing) if you're including the hand-tool pegboard section, either as a separate CNC operation on the 4mm hardboard or purchased pre-drilled pegboard trimmed to size.
Assembly
- Dry-fit the entire carcass before any glue goes down โ dados should seat with light hand pressure, not require force or leave visible gaps. Adjust pocket depths in your CAM file and re-cut if anything binds or rattles.
- Glue and clamp the carcass square, checking diagonal measurements corner-to-corner rather than trusting a framing square alone on a piece this size โ equal diagonals confirm a square box far more reliably.
- Install threaded inserts for the leveling feet into the bottom panel before standing the chest upright; it's much easier to drive inserts into a panel laid flat on the bench than reaching up into a finished carcass.
- Assemble each drawer box with glue and brad nails or small screws, then test-fit it dry in its opening before attaching slides โ catching a drawer box that's a hair too wide now saves you from fighting binding slides later.
- Mount the drawer slides per the hardware's spacing instructions, keeping both the cabinet-side and drawer-side members perfectly level and parallel โ even a millimeter of misalignment front-to-back will make a drawer bind or rack.
- Attach pulls, hang the pegboard back panel on standoffs so tools have clearance to hang, and give every edge-banded surface a final light sand before finishing.
Finishing
Iron on edge banding to cover all exposed plywood edges before finishing โ it's far easier to trim banding flush with a sharp blade and sand it level while the piece is still in sub-assemblies than after final glue-up. A few coats of danish oil wiped on and buffed out gives plywood furniture a durable, low-maintenance finish that won't show tool grease and handling marks the way a glossy polyurethane would in daily shop use.
Safety Notes
Plywood dust from an 18mm sheet is a lot of material removed fast โ run dust collection at the router and wear a properly rated dust mask or respirator even for "just wood," since plywood dust includes the glue layers between veneers, which some people find more irritating than solid lumber dust. Support full sheet stock properly before cutting; an unsupported overhang on a 4x8 sheet can tip a hold-down table or flex enough to throw off your cut depth mid-pass. Once the chest is loaded with tools, it will be heavy โ level it on its feet before filling drawers, and don't fill the top drawers first on a tall, narrow design, since a top-heavy loaded chest can tip.
Closing Thoughts
The real payoff of building this on a CNC rather than by hand isn't the joinery โ dados are easy enough with a router table โ it's that the whole design lives as a file. Once you've built one chest sized to your tools, resizing drawer heights, adding a second column, or cutting a matching smaller version for a second workstation is an afternoon of editing numbers, not a redesign from scratch.